mercoledì 19 novembre 2014

PlcRelay8UDP 1.0.0 for Android and Iphone

Work in progress  PlcRelay8UDP 1.0.0 for Android and Iphone

KMTronic LAN Ethernet IP 8 channels UDP Relay board 

 

 

mercoledì 12 novembre 2014

PlcRelay2UDP 1.0.0 for Android


Finally after a few months I was able to complete the Android version of the program PlcRelay2UDP

The UDP version of the card controls the relay as a switch On and Off, and not as a button to change status

UDP Relay 2 TCP control PRO

 

 

 

domenica 25 maggio 2014

Plc 2 Relay On Off UDP for Android, iPhone e iPad

"Plc 2 Relay On Off UDP" Version 1.0.0 is almost ready to be released.
This pilot program the card Kmtronic (c) equipped with two relays.
This program allows you to send the signal "on" and "off" to the relay.
The UDP version has the commands "On" and "Off" unlike the version that has the TCP command sends impulse relay so the relay is actuated and the value is reversed.


The version for iPhone and iPad is ready show on App Store.

A short version for Android will be published on Google Play Store.



"Plc 2 Relay On Off UDP" versionè 1.0.0 è quasi pronto per essere rilasciato.
Questo programma pilota la scheda della Kmtronic (c) equipaggiata con due relè.
Questo programma permette di inviare il segnale di "on" e di "off" al relè.
La versione UDP ha i comandi "On" ed "Off" a differenza della versione TCP che ha il comando invia impulso a relè per cui il relè viene azionato e il valore viene invertito. 


La versione per iPhone e iPad è pronta ed è stata approvata da Apple
 

giovedì 22 maggio 2014

Plc 2 Relay On Off UDP for Android iPhone and iPad in prepared.

Switch Control Relay Ethernet with Android, iPhone and iPad

The development has not been easy

Soon will be available on AppSotre and PlayStore..

This program allows you to control the Relay KMTronic (C) UDP version , fantastic hardware that can turn on and off 2 relays connected to a LAN network .

Thanks a Frédéric Fitaire.

mercoledì 21 maggio 2014

Plc 8 Relay On Off for iPhone and iPad Version (2.0.0) is Approved


Apple has approved version 2.0.0 of Plc 8 Relay On Off for iPhone and iPad Version.
This version of it is available on this link.

This new version is update the App. with these new features:
- On the Settings screen:
a) Check: Control relay alway status;
b) If the check (a) is disabled, you can enable the control All on Clicking in Relay.  (this means that all the relays are checked only when you press on a relay).
- On Home:
- If Check (A) is active display signal (Signal blinking yellow and green. When the signal is blocked on a color, it means that the link is no longer good, if it turns red there is no more connection.)

martedì 20 maggio 2014

(work in progress) Plc 2 Relay On Off for iPhone and iPad Version (2.0.0)

The version 2.0.0 is almost ready. 
This version include: 
- Animation on relay;
- Label on relay; 
- Led connection on card

lunedì 19 maggio 2014

Plc 8 Relay On Off for iPhone and iPad Version (2.0.0)

Recently I sent to Apple the version 2.0 of the program Plc8RelayOnOff.

In 3G networks can be useful not read the status of relays continuously, we read the state at the time of the connection, and if we want at the time you activate a relay.

This new version is update the App. with these new features:
- On the Settings screen:
a) Check: Control relay alway status;
b) If the check (a) is disabled, you can enable the control All on Clicking in Relay.  (this means that all the relays are checked only when you press on a relay).
- On Home:
- If Check (A) is active display signal (Signal blinking yellow and green. When the signal is blocked on a color, it means that the link is no longer good, if it turns red there is no more connection.)

If the check (A) is enabled Check (B) is disabled

This update is designed to give the user the option of not continually check the status of the relay.



Da poco ho inviato ad Apple per l'approvazione la versione 2.0 del programma Plc8RelayOnOff.

Questa nuova versione aggiorna l'App. con queste nuove funzionalità:
- Nella schermata Impostazioni ho inserito:
a) Check: Control alway status relay;
b) Se il Check (a) è disabilitato si può abilitare il Check control All on Click. (questa fa si che tutti i relè vengono controllati solo quando si preme su un relè).

Se il Check (A) è abilitato il Check (B) viene disabilitato

- Nella schermata di Home:
c)  Se il Check (A) è abilitato viene visualizzato un pallino lampeggiante di colore Giallo/Verde. (Quando il segnale si blocca su un colore, vuol dire che il collegamento non è più buono, se diventa rosso non c'è più collegamento. )


Questo aggiornamento nasce per dare la possibilità all'utente di non controllare continuamente lo stato dei relè. 

giovedì 8 maggio 2014

Plc 8 Relay On Off for iPhone and iPad Version (1.0.0)

(Switch Control Relay Ethernet with iPhone and iPad)


This program allows you to control the relay of the Board KMTronic (C) , fantastic hardware that can turn on and off 8 relays connected to a LAN network . (Relay Ethernet iPhone  Kmtronic )
The configuration is very simple, after installing the program, go to Settings ( gear), a panel opens pre-filled with the sample data , you will need to replace the existing data with those you have set in your card and click on the "Save" button .

If the parameters are correct, click on "Local Connect / DNS Connect" you will see eight icons in the shape of the lamp (turned off if the relay is OFF, if the relay is switched ON)
If you have set the DNS , the web address to access the board from outside ( 3G, Lan external ) by clicking on " DNS Connect" you will see two icons in the shape of the lamp ( turned off if the relay is OFF , on if the relay is ON )

IMPORTANT , to use the "DNS Connect" you have to set your router so that it is directed on the relay board is used when access from outside the doorway indicated by you

Link AppStore

ITALIANO
Questo programma consente di pilotare i relè della Scheda  KMTronic (C), fantastico hardware in grado di accendere e spegnere 8 relè collegati ad una rete lan.

La configurazione è molto semplice, dopo aver installato il programma, andare in impostazioni (ingranaggio),

si aprirà un pannello già compilato con i dati di esempio, dovrete sostituire i dati esistenti con quelli che avete impostato nella vostra scheda e cliccare sul pulsante "Save".

Se i parametri sono esatti, cliccando su "Local Connect" vi appariranno otto icone a forma di lampada (spenta s
e il relè è OFF, accesa se il relè è ON)

Se avete impostato il DNS, l'indirizzo web per accedere alla scheda dall'esterno, (reti 3G, Lan esterne) cliccando su "DNS Connect" vi appariranno due icone a forma di lampada (spenta se il relè è OFF, accesa se il relè è ON)

IMPORTANTE, per utilizzare il "DNS Connect" dovete impostare il vostro router affinché venga indirizzato sulla scheda relè quando viene utilizzato l'accesso dall'esterno sulla porta da voi indicata

martedì 8 aprile 2014

Plc 2 Relay On Off for iPhone and iPad Version (1.0.0)




Switch Control Relay Ethernet with iPhone and iPad

ENGLISH
After I gathered on the many requests , I decided to create this program for the Iphone.

The development has not been easy ,  it is very similar to the Android version , in this version I have not yet implemented the timer, which will be implemented in future versions .

This program allows you to control the Relay KMTronic (C) , fantastic hardware that can turn on and off 2 relays connected to a LAN network .

The configuration is very simple, after installing the program , go to Settings ( gear)  , a panel opens prefilled with the sample data , you will need to replace the existing data with those you have set in your card and click on the button "Save ".

If the parameters are correct, click on "Local Connect" you will see two icons in the shape of the lamp ( turned off if the relay is OFF, if the relay is switched ON)

If you have set the DNS , the web address to access the board from outside ( 3G, Lan external ) by clicking on " DNS Connect" you will see two icons in the shape of the lamp ( turned off if the relay is OFF , on if the relay is ON )

IMPORTANT , to use the "DNS Connect" you have to set your router so that it is directed on the relay board is used when the external access on port you specify.Dopo le tante richieste pervenutemi, ho deciso di realizzare questo programma per Iphone.

Link App Store 

ITALIANO
Lo sviluppo non è stato semplice, ma alla fine l'applicazione è stata realizzata, è molto simile alla versione per Android, in questa versione non ho ancora implementato il timer, che verrà implementato nelle prossime versioni.

Questo programma consente di pilotare il Relè della KMTronic (C), fantastico hardware in grado di accendere e spegnere 2 relè collegati ad una rete lan.

La configurazione è molto semplice, dopo aver installato il programma, andare in impostazioni (ingranaggio),
si aprirà un pannello già compilato con i dati di esempio, dovrete sostituire i dati esistenti con quelli che avete impostato nella vostra scheda e cliccare sul pulsante "Save".

Se i parametri sono esatti, cliccando su "Local Connect" vi appariranno due icone a forma di lampada (spenta se il relè è OFF, accesa se il relè è ON)

Se avete impostato il DNS, l'indirizzo web per accedere alla scheda dall'esterno, (reti 3G, Lan esterne) cliccando su "DNS Connect" vi appariranno due icone a forma di lampada (spenta se il relè è OFF, accesa se il relè è ON)

IMPORTANTE, per utilizzare il "DNS Connect" dovete impostare il vostro router affinché venga indirizzato sulla scheda relè quando viene utilizzato l'accesso dall'esterno sulla porta da voi indicata.


domenica 5 gennaio 2014

Plc 2x5 Relay Pro

ENGLISH
This new program allows you to manage 5 cards that are equipped with 2 relays each.

The program allows you to manage the parameters for every single card, by the IP / DNS and  door.

I also added the parameter Label for each relay.

The connection test is done after you click on the connect button, this test is performed only on the 1st relay, it is assumed that if there is access to the 1st will be the same for others.

Sampler setting router:
myaddress.dyndns.org:8091 (192.168.1.191 port in/out 8091 tcp)
myaddress.dyndns.org
:8092 (192.168.1.192 port in/out 8092 tcp)
myaddress.dyndns.org
:8093 (192.168.1.193 port in/out 8093 tcp)
myaddress.dyndns.org
:8094 (192.168.1.194 port in/out 8094 tcp)
myaddress.dyndns.org
:8095 (192.168.1.195 port in/out 8095 tcp)

ITALIANO
Questo nuovo programma permette di gestire 5 schede che montano 2 relè ognuna.

Il programma permette di gestire i parametri per ogni singola scheda, dall'IP/DNS alle porte.

Ho aggiunto anche il parametro Etichetta/Label per ogni singolo relè.

Il test di connessione/comunicazione avviene dopo che si clicca sul pulsante connetti, questo test viene eseguito solo sul 1° relè, si suppone che se vi è l'accesso al 1° lo stesso avverrà per gli altri.